3 recalls found. |
DEFECT #1 - SEAT BELTS:FRONT:ANCHORAGE
Posted on: 1994-08-18
Description
In a fmvss no. 208 30 miles-per-hour compliance test, an unbelted test driver dummy's chest maximum resultant acceleration was 70.8 g's, which exceeds the maximum allowable value of 60 g's. Also, the unbelted passenger dummy's left femur maximum load was 2361 lbs, which exceeds maximum allowable value of 2250 lbs. The vehicles do not comply with fmvss no. 208, occupant crash protection.
Consequence
Consequence of non-compliance: in the event of an accident, the occupant will be subjected to an increased risk of injury.
Corrective Action
On automatic transmission models only, the dealer will replace the transmission support crossmember with a crossmember used on the manual transmission model. Also, the transmission rear bushing supports will be replaced with bushing having different performance characteristics. The steering column front support bearing at the firewall will be replaced with a modified part using a teflon inner surface and teflon spray will be applied to the column housing in the area of the bearing. A brace will be added between the knee bolster support and the steering column.
Notes
System: interior systems; passive restraints; air bag; driver; fmvss n0. 208.vehicle description: passenger cars, models 325i, 325ia, 325is, 325sa, and m3.note: if your vehicle is presented to an authorized dealer on an agreed upon service date and the remedy is not provided free of charge within a reasonable time or the remedy does not correct the noncompliance, please contact bmw service center at 1-800-831-1117. Also, contact the national highway traffic safety administration's auto safety hotline at 1-800-424-9393.
DEFECT #2 - FUEL SYSTEM, GASOLINE:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS
Posted on: 1994-04-13
Description
Feed fuel hoses can harden and set over time, allowing a seepage of fuel at the connection between the hose and the engine fitting. The clamp used to hold the hose to the fitting is unable to compensate for the hardening of the feed fuel hose.
Consequence
Fuel seepage between the feed fuel hose and the engine fitting can result in free fuel in the engine compartment, which could result in a fire when exposed to a source of ignition.
Corrective Action
A redesigned feed fuel hose and hose clamp will be installed to alleviate the fuel seepage.
Notes
System: fuel; fuel line fittings; metallic.vehicle description: passenger vehicles; models 318i, 318si, 318ic, 325i, 325is, 325ix, 325ic, 525i, 535i, 735i and 735il.note: if your vehicle is presented to an authorized dealer on an agreed upon service date and the remedy is not provided within a reasonable time and free of charge, or the remedy does not correct the defect or noncompliance, please contact bmw at 1-800-831-1117. Also, contact the national highway traffic safety administration's auto safety hotline at 1-800-424-9393.
DEFECT #3 - VISIBILITY:DEFROSTER/DEFOGGER SYSTEM:WINDSHIELD:HEATER CORE
Posted on: 1993-02-05
Description
The malfunction or failure of a coolant system component results in significantly increased coolant temperature and a resulting increase in system pressure.
Consequence
Vehicles operated under this increased cooling systempressure condition can suffer damage or failure of parts of the cooling systemsuch as (1) leakage from a coolant hose, (2) leakage of the radiator orexpansion tank, (3) disconnection of a hose from a pipe or a fitting, and (4)cracks in the heater core end piece resulting in coolant leakage. In some cases,boiling coolant can contact the lower right leg of the driver resulting inburns. Also, escaping coolant in the passenger compartment can cause vaporfogging of the interior surface of the windows, reducing driver visibility.
Corrective Action
Dealers will install a thermostatic bypass valve in the engine compartment to control coolant temperature in the heater core. Also, a new design radiator cap will be installed, to control pressure and provide greater coolant overflow in the event of overheating.
Notes
System: coolant system.vehicle description: passenger cars.