19 recalls found. |
DEFECT #1 - SERVICE BRAKES, AIR:DISC:CALIPER
Posted on: 2010-11-02
Description
Paccar is recalling certain model year kenworth t660, t700, t800 and w900 vehicles manufactured from december 22, 2008, through august 2, 2010, and equipped with ag400l air disc brakes. The air disc brake caliper could be installed on the wrong side of the drive axle potentially causing interference with the suspension bracket and the rear suspension as the outermost brake pads wear and the floating caliper moves inboard.
Consequence
As this interference gets larger, this could eventually lead to reduced braking performance, increasing the risk of a crash.
Corrective Action
Dealers will verify the correct orientation of the brake caliper and perform the necessary repair free of charge. The safety recall began on november 24, 2010. Owners may contact kenworth at 425-828-5440.
Notes
Kenworth safety recall no. 10kwh.owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.safercar.gov .
DEFECT #2 - PARKING BRAKE:CONVENTIONAL:AIR
Posted on: 2008-03-21
Description
Paccar is recalling 1,043 my 2008-2009 kenworth c500, t2000,t660, t800 and w900 trucks equipped with bendix mv-3 dash control valves. The molded valve body has an incorrect core pin in the injection mold causing the valve body to be oversized in the double check valve area. This condition can allow the rubber double check valve to become lodged in the body opening under certain circumstances.
Consequence
If the double check valve becomes lodged, in the event of a primary reservoir failure, air pressure can leak past the lodged double check valve thereby depleting the secondary reservoir, causing reduced ability for modulating the service emergency brakes. In such an event, the operator should observe an air leak, indications of low air pressure via the primary and secondary air gauges, and audible and visual low air pressure warning alarms. A vehicle crash is possible if these warnings are not heeded.
Corrective Action
Dealers will replace the bendix mv-3 dash control valves free of charge. The recall began on april 14, 2008. Owners may contact kenworth at 1-425-828-4196.
Notes
Kenworth recall no. 08kw3 and peterbilt recall no. 308e.customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.safercar.gov.
DEFECT #3 - POWER TRAIN:AXLE ASSEMBLY
Posted on: 2009-10-27
Description
Kenworth is recalling model year 2009 through 2010 t2000, t800, t660 and w900 trucks manufactured between november 12, 2008 and september 30, 2009. The axle u-bolts attaching the axle to the suspension leaf spring on certain ag400l rear suspensions may have received insufficient fastener torque during the installation process. The insufficient torque may allow the axle u-bolt to become loose, which may cause vibration in the rear suspension.
Consequence
If multiple fasteners were to become loose, the rear axle may shift relative to the rear suspension leaf spring, which can result in loss of control and a crash.
Corrective Action
Dealers will inspect the axle u-bolts for visible defects, including bent and/or smashed threads and re-torque the axle u-bolts to factory specifications. The recall began on november 4, 2009. Owners may contact kenworth at 425-828-5440.
Notes
Kenworth recall no. 09kwa.owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.safercar.gov .
DEFECT #4 - TRAILER HITCHES
Posted on: 2008-03-10
Description
Paccar is recalling 318 my 2007-2009 kenworth t800, w900, and peterbilt 357, 365, 367, 378, 379, 384, 385, 386,388, and 389 trucks equipped with premier trailer hitch assemblies. The pintle hitch assemblies may have been manufactured in a manner resulting in a reduction of fatigue strength of the pivot pins.
Consequence
This reduction of fatigue strength could cause the pivot pin to crack and eventually break, causing the trailer to detach from the truck while in motion, which could cause a crash that could result in personal injury or death.
Corrective Action
Dealers will replace the potentially defective pivot pin free of charge. The recall began on april 18, 2008. Owners may contact kenworth at 1-425-828-5440 or peterbilt at 1-940-591-4196.
Notes
Kenworth recall no. 08kw4 and peterbilt recall no.208d.customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.safercar.gov.
DEFECT #5 - SERVICE BRAKES, AIR:DISC
Posted on: 2008-08-25
Description
Paccar is recalling 86 my 2009 kenworth t660, t800, w900, and peterbilt 386, 365, and 388 trucks equipped with bendix front air disc brakes. The size 14 service chamber of certain front air disc brakes may have been contaminated with grease between the piston head/plate and the diaphragm. When braking pressure is applied, the grease may allow the piston head/plate to slip off center and catch on the reducing ring of the size 14 service chamber.
Consequence
The catching of the piston head/plate on the reducing ring may lock up the corresponding front air disc brake which may impact the operator's ability to steer or control the vehicle.
Corrective Action
Dealers will replace both front air disc brakes size 14 service chambers free of charge. The recall began on august 27, 2008. Owners may contact kenworth at 1-425-828-5440 and peterbilt at 1-940-591-4196.
Notes
Kenworth recall no. 08kwa and peterbilt recall no. 708f.customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.safercar.gov.
DEFECT #6 - SUSPENSION
Posted on: 2008-09-24
Description
Paccar is recalling 130 my 2004-2009 t2000, t800, t600, w900 and t660 kenworth trucks built with an ag400 rear suspension, long stroke brake chambers, and wide base tires (super singles). These vehicles may develop an increase in lateral and vertical axle movement. This movement may cause part or parts of the brake assembly (brake cam tube support, brake chamber bracket, brake chamber, brake spider) to develop fatigue cracks, possibly resulting in the failure of the part or parts within the brake assembly.
Consequence
A failure may reduce vehicle brake performance, increasing the risk of a crash.
Corrective Action
Dealers will install the cam tube support brackets on all of the rear axle wheel ends. Inspect the rear axle brake assembly and replace it if cracked. The recall is expected to begin during november 2008. Owners may contact kenworth at 1-425-828-5440.
Notes
Kenworth recall no. 08kwb. Customers may contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.safercar.gov.
DEFECT #7 - ENGINE AND ENGINE COOLING:ENGINE:DIESEL
Posted on: 2008-09-25
Description
Paccar is recalling 263 my 2008-2009 kenworth t800, w900 and peterbilt 365 and 384 trucks equipped with c7 or c9 caterpillar diesel engines. The fuel pump outlet check plug may be cracked which could cause fuel to spray and leak.
Consequence
Fuel leakage, in the presence of an ignition source, could result in a fire.
Corrective Action
Paccar is working with caterpillar (please see 08e042). Caterpillar will replace the fuel pump plug free of charge. The recall is expected to begin during september 2008. Owners may contact caterpillar at-1-800-447-4986 or kenworth at 1-425-828-5440 or peterbilt at 1-940-591-4196.
Notes
Kenworth recall no. 08kwc and peterbilt recall no. 908h.customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.safercar.gov.
DEFECT #8 - ENGINE AND ENGINE COOLING:ENGINE:DIESEL
Posted on: 2008-09-25
Description
Paccar is recalling 4,883 my 2006-2009 kenworth t600, t660, t800, w900, t2000 and my 2008-2009 peterbilt 365, 367, 379, 384, 386, 387, 388 and 389 trucks. Inadequate stiffness of the diesel particulate filter (dpf) bracket could result in separation of the dpf from the chassis.
Consequence
A vehicle crash could occur if another vehicle strikes the dpf on the roadway.
Corrective Action
Paccar is working with caterpillar to repair these vehicles (please see 08e041). Owners may contact caterpillar at 1-800-447-4986 or kenworth at 1-425-828-5440 or peterbilt at 1-940-591-4196.
Notes
Kenworth recall no. 08kwd and peterbilt recall no. 908g.customers may contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.safercar.gov.
DEFECT #9 - FUEL SYSTEM, OTHER:STORAGE:TANK ASSEMBLY
Posted on: 2011-02-25
Description
Paccar is recalling certain model year 2008-2012 kenworth t2000, t660, t700, t800, and w900, as well as model year 2009-2012 peterbilt 365, 367, 384, 386, 387, 388, 389, and 587 trucks equipped with paccar mx engines. The oil module centrifugal spinner filter cap in the paccar mx engine may become loose, possibly allowing the cap to come off and engine oil to partially discharge from the oil module onto exhaust components.
Consequence
The discharge of engine oil onto exhaust components which are hot, such as when the engine is under significant load, may cause a fire.
Corrective Action
Dealers will re-torque the oil module filter cap and install a secondary retention device on the secondary centrifugal spinner filter cap. This service will be performed free of charge. The safety recall is expected to begin during march 2011. Owners may contact kenworth at 1-425-828-5440 and peterbilt at 1-940-591-4196.
Notes
Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.safercar.gov .
DEFECT #10 - SUSPENSION
Posted on: 2008-07-14
Description
Kenworth is recalling 1,189 my 2009 t2000, t600, t660, t800 and w900 trucks. The axle u-bolts attaching the axle to the drive beam on certain ag380 rear suspensions may have received insufficient fastener torque during the installation process.
Consequence
The insufficient torque may allow the axle u-bolt to loosen if undetected, could impact long term suspension performance and increase the risk of a crash.
Corrective Action
Dealers will have the axle u-bolt on the affected chassis re-torqued to factory specifications free of charge. The recall began on august 12, 2008. Owners may contact kenworth at 425-828-5440.
Notes
Kenworth recall no. 08kw9.customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.safercar.gov.
DEFECT #11 - SERVICE BRAKES, AIR
Posted on: 2009-06-29
Description
Kenworth is recalling 3,423 my 2004-2009 t2000, t800,t600, w900 and t660 vehicles. Increased brake excitation in a certain vehicle configuration which includes bendix drum brakes, wide base low profile single tires, and an ag400 or ag460 rear suspension, due to its unique brake clocking and cam tube length, can cause fatigue and cracking to brake assembly components.
Consequence
Cracking can cause a complete fracture of the cam tube, which could increase stopping distance and decrease parking brake hold capability.
Corrective Action
Dealers will inspect the rear axle brakes assembly, replace cracked rear axle brakes assembly components where required, and install cam tube support brackets on all rear axle wheel ends free of charge. The recall is expected to begin or before july 25, 2009. Owner may contact kenworth at 1-425-828-5440.
Notes
Paccar recall no. 09kw7.owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.safercar.gov .
DEFECT #12 - STEERING:COLUMN
Posted on: 2009-07-08
Description
Paccar is recalling 2,096 my 2009 kenworth and peterbilt vehicles equipped with trw steering shafts. Mislocation of a circumferential weld may allow the splined tube and non-splined tube to rotate relative to one another during a low speed, high torque turn, possibly resulting in a separation of the two tubes.
Consequence
A separation of the splined and non-splined tubes could cause a loss of steering control and increase the risk of a crash.
Corrective Action
Dealers will inspect the steering shaft using a weld placement gauge and miswelded steering shaft will be replaced free of charge. The recall began july 31, 2009. Owners may contact kenworth at 1-425-828-5440 and peterbilt at 1-940-591-4196.
Notes
Kenworth recall no. 09kw8 & peterbilt recall no. 609-c.owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.safercar.gov .
DEFECT #13 - STEERING:COLUMN
Posted on: 2010-07-02
Description
Paccar is recalling certain model year 2008-2010 trucks equipped with trw steering shafts. The circumferential weld around the steering shaft tube that welds the splined tube to the non-splined tube may be mislocated. Mislocation of the circumferential weld may allow the splined tube and non-splined tube to rotate relative to one another during a low speed, high torque turn, possibly resulting in a separation of the two tubes.
Consequence
A separation of the splined and non-splined tubes would cause a loss of steering control and increase the risk of a vehicle crash.
Corrective Action
Dealers will inspect the steering shaft using a weld placement gauge provided by trw. Any steering shaft found to have been welded improperly will be replaced free of charge. The safety recall began on july 30, 2010. Owners may contact kenworth at 425-828-5440 and peterbilt at 940-591-4196.
Notes
Kenworth's recall campaign number is 10kw-f & peterbilt recall no. 0610-d. Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.safercar.gov .
DEFECT #14 - SERVICE BRAKES, AIR:DISC
Posted on: 2009-05-19
Description
Paccar is recalling 140 my 2005, 2007-2009 t800, w900, and t660 trucks. The caliper mounting fasteners attaching the air disc brake caliper assembly to the torque plate may have received insufficient torque during the installation process. The insufficient torque may allow the air disc brake caliper assembly to become loose and possibly separate from the vehicle.
Consequence
This could result in reduced braking capacity and also a road debris hazard, increasing the risk of a crash.
Corrective Action
Dealers will inspect air disc brake caliper assemblies and replace the caliper mounting fasteners and torque properly. This service will be performed free of charge. The manufacturer has not yet provided an owner notification schedule. Owners may contact kenworth at 1-425-828-5440.
Notes
Kenworth recall no. 09kw3.owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.safercar.gov .
DEFECT #15 - SERVICE BRAKES
Posted on: 2013-11-21
Description
Paccar is recalling certain model year 2007-2014 kenworth t800 and w900 trucks manufactured march 22, 2006, through july 15, 2013 and equipped with primaax tridem rear suspensions and a pusher and/or tag axle. The affected trucks have brake chambers that take longer to apply or release the brakes than the required time limit. Thus, these vehicles fail to conform to the requirements of federal motor vehicle safety standard (fmvss) no. 121, air brake systems.
Consequence
Brakes that take longer to apply may lengthen the distance needed to stop the truck, increasing the risk of a crash.
Corrective Action
Paccar will notify owners, and dealers will modify the air brake system, free of charge. The recall began on january 15, 2014. Owners may contact paccar at 1-425-468-7400. Kenworth's recall number is 13kwl.
Notes
Owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.safercar.gov.
DEFECT #16 - SERVICE BRAKES, AIR:ANTILOCK:ABS WARNING LIGHT
Posted on: 2020-04-07
Description
Paccar incorporated (paccar) is recalling certain 2008-2019 peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 kenworth t170, t270, t370, t660, t680, t800, t880, and w900 vehicles equipped with namux software. In the event that the anti-lock brake system (abs) loses battery and/or ignition power to the controller, the dash warning light for the abs may not illuminate to warn the driver of the loss of abs. As such, these vehicles fail to comply with the requirements of federal motor vehicle safety standard (fmvss) number 121, air brake systems, and 136, electronic stability control system on heavy vehicles.
Consequence
If the driver unknowingly operates the vehicle without the abs functioning, there would be an increased risk of a crash.
Corrective Action
Paccar will notify owners, and dealers will update the namux software within the cab control module, free of charge. Paccar issued owners an interim notification on june 4, 2020. The recall began may 26, 2020. Owners may contact kenworth customer service at 1-425-828-5888 or peterbilt customer service at 1-940-591-4220. Paccar's number for this recall is 20pbc and 20kwb.
Notes
Owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.safercar.gov.
DEFECT #17 - ELECTRONIC STABILITY CONTROL
Posted on: 2020-04-07
Description
Paccar incorporated (paccar) is recalling certain 2008-2019 peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 kenworth t170, t270, t370, t660, t680, t800, t880, and w900 vehicles equipped with namux software. In the event that the anti-lock brake system (abs) loses battery and/or ignition power to the controller, the dash warning light for the abs may not illuminate to warn the driver of the loss of abs. As such, these vehicles fail to comply with the requirements of federal motor vehicle safety standard (fmvss) number 121, air brake systems, and 136, electronic stability control system on heavy vehicles.
Consequence
If the driver unknowingly operates the vehicle without the abs functioning, there would be an increased risk of a crash.
Corrective Action
Paccar will notify owners, and dealers will update the namux software within the cab control module, free of charge. Paccar issued owners an interim notification on june 4, 2020. The recall began may 26, 2020. Owners may contact kenworth customer service at 1-425-828-5888 or peterbilt customer service at 1-940-591-4220. Paccar's number for this recall is 20pbc and 20kwb.
Notes
Owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.safercar.gov.
DEFECT #18 - SERVICE BRAKES, AIR:ANTILOCK:ABS WARNING LIGHT
Posted on: 2020-04-07
Description
Paccar incorporated (paccar) is recalling certain 2008-2019 peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 kenworth t170, t270, t370, t660, t680, t800, t880, and w900 vehicles equipped with namux software. In the event that the anti-lock brake system (abs) loses battery and/or ignition power to the controller, the dash warning light for the abs may not illuminate to warn the driver of the loss of abs. As such, these vehicles fail to comply with the requirements of federal motor vehicle safety standard (fmvss) number 121, air brake systems, and 136, electronic stability control system on heavy vehicles.
Consequence
If the driver unknowingly operates the vehicle without the abs functioning, there would be an increased risk of a crash.
Corrective Action
Paccar will notify owners, and dealers will update the namux software within the cab control module, free of charge. Paccar issued owners an interim notification on june 4, 2020. The recall began may 26, 2020. Owners may contact kenworth customer service at 1-425-828-5888 or peterbilt customer service at 1-940-591-4220. Paccar's number for this recall is 20pbc and 20kwb.
Notes
Owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.safercar.gov.
DEFECT #19 - ELECTRONIC STABILITY CONTROL
Posted on: 2020-04-07
Description
Paccar incorporated (paccar) is recalling certain 2008-2019 peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 kenworth t170, t270, t370, t660, t680, t800, t880, and w900 vehicles equipped with namux software. In the event that the anti-lock brake system (abs) loses battery and/or ignition power to the controller, the dash warning light for the abs may not illuminate to warn the driver of the loss of abs. As such, these vehicles fail to comply with the requirements of federal motor vehicle safety standard (fmvss) number 121, air brake systems, and 136, electronic stability control system on heavy vehicles.
Consequence
If the driver unknowingly operates the vehicle without the abs functioning, there would be an increased risk of a crash.
Corrective Action
Paccar will notify owners, and dealers will update the namux software within the cab control module, free of charge. Paccar issued owners an interim notification on june 4, 2020. The recall began may 26, 2020. Owners may contact kenworth customer service at 1-425-828-5888 or peterbilt customer service at 1-940-591-4220. Paccar's number for this recall is 20pbc and 20kwb.
Notes
Owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.safercar.gov.